I found a Tamiya Jeep just now, but the pin-up girls I was thinking of combining were fixed to a small pedestal. But since I found it, I will assemble it. I found two boxes; I only need to assemble one.
There were some paint instructions during the assembly of the chassis. I don’t have to paint it yet. I’ll go ahead with the assembly a little more.
Few parts fit well, so the work goes smoothly.
When I installed the tire, it was gradually completed.
Open the hood; the engine is reproduced properly, so it’s incredible. This time, the hood is closed, so I think I’ll proceed without painting.
(2020/08/23)
I think Willys Jeep, Schwimmwagen, and Kübelwagen were released in light vehicles of Tamiya relatively simultaneously. I thought I had made them at least once, but this might be my first Jeep. It’s straightforward to make, just like the other two cars.
Jeep with wire cutter attached. Equipped with a Browning machine gun, this stylish Jeep is active on the front line.
The handle is fixed to fine-tune the figure’s pose. It’s tight when you put the handle on. I will leave the handle and both hands as they are until the adhesive hardens, but will they fit in the driver’s seat after painting?
The figure attached to the jeep kit looks like this. I think it’s not bad. This time, instead of this head, I will try to replace it with a resin head. From this direction, I feel somewhat like former President Ronald Wilson Reagan.
(2020/08/25)
After changing the head and shaping around the neck, I tried to apply a light gray Tamiya because there was no gray surfacer. The color is quite dark. It’s been a long time since I last used it.
The middle is the shell of a cicada. It was a bit hot day after day in Kanto. The temperature dropped a little yesterday, and summer will finally end. I am thinking of duplicating the remaining parts of the kit I made before and putting it on the Jeep. I made this with epoxy putty using a mold made of silicone that is heated to soften. I wonder if Tamiya’s epoxy pate is good because it has a high viscosity.
I’m preparing to paint by bonding the load and masking the windshield.
I used Tamiya acrylic olive drab after a long time. Tamiya acrylic is very matte, as usual.
I pasted the decals. By the way, before I pasted the decal, I blew clear on the part to improve the adhesion of the decal. Once it dries, I will protect the decal by coating it with matte clear.
(2020/08/27)
The Jeep under the building is completed. Tamiya explains that it was studied after seeing small military vehicles like the German army’s Kübelwagen.
They have developed a four-wheel drive, lightweight, rugged, mass-produced vehicle. To cope with mass production, American bantam was the first company and they had Willis and Ford make trial manufacture and modification, and officially adopted it. By August 1945, 640,000 units had been produced.
If I had a production function in a simulation game, I’d only produce Panzer tanks or Sherman tanks, but in the real world, they had to produce small vehicles and trucks like this, and it will be hard for those who make plans. It was hard because they had to think about aircraft and ships and develop new weapons. The simulation game Hearts of Iron III have a set rail, but we never know what the future events are.
The German army held out a lot. The marking is the 7th Armored Division “Lucky Sevens” No. 814 Tank Destroyer Battalion and Reconnaissance Company, Car number 22, in Belgium in January 1945. Come to think of it, it’s been more than half a year since Normandy, but the front is still somewhere around Belgium.
A US Army soldier was holding the wheel in a relaxed pose.
I used a dry metallic brush to light up the wire cutter at the head.
Because clear parts are used for the headlight, it became pretty realistic.
If I put the stowage on the Jeep, it feels like working hard in the front line.
Is it an identification of friend and foe by Allied aircraft? The significant star mark on the hood is a design I would like for US military vehicles.
I hesitated because it was a small car, but I made it a little more dirty weathering. I’ve just started building a Jeep crew kit of Miniart, so I want to put one more person in the end. I want to try weathering a lot if there are many people in a car or AFV.
(2020/08/29)
コメント